Brand

Rating

Price

Special Offers

Contact Diameter

Overall Length

Shank Diameter

Stem Type

Tool Type

Additional Features

Accuracy

Material

Product Type

Range

Precision Measuring Tools - Free UK Delivery Over £25 - Buy Online | Zoro

For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Cylinder Type
For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Consists of a chuck body and four contact arms. Designed to check ‘run-out’ or concentricity, straightness and alignment. Will indicate the position of a datum point on a component or fixture from the centre line of a machine spindle. Suitable for use on drill presses, lathes, milling machines, borers etc. 

Chuck Body:  
Held in the spindle using a suitable drill chuck or collet chuck (fig 1). The contact arms are retained in position using the knurled collar which lightly clamps the ball joint inside the body. Arms may be exchanged without the need to remove the body from the machine spindle. 

Universal Indicator Holder 
The detachable end will allow clamping with 2 and 3 piece dovetail clamping assemblies and when removed will fit standard 1/4” side clamp. This uses the spindle centre line to align component bores or spigots, check the flatness or squareness of workpieces or fixturing and check run-out of components. The spindle should only be rotated manually to avoid damaging the dial test indicator (fig 1).

Needle Point
To lightly mark out lines and positions on a component as a guide to subsequent operations, using the machine’s dials or digital read-out to position the scriber point (not illustrated). 

Position the contact arm in line, but slightly away from the surface to be aligned. When finding the surface of a diameter, the ‘Disc' must be positioned as near to the centre of that diameter as possible. Run the spindle between 200 and 500 revs/min. The table or spindle is then moved slowly, to bring the contact arm closer to the surface to be aligned. The contact arm will tap lightly against the surface (fig 2) the movement of the arm will become less and less the nearer the datum point gets to the spindle centre line (fig 3). When the arm stops spinning in a straight line and starts to 'jump', this indicates the datum point (fig 4):   
1/2 contact dia + Edge = Centre       
1/2 contact dia - Centre = Edge

Ball Contact  .250”
Used to find a datum  point .125” ± .0005” away from a flat surface.

Disc Contact  .100”  
Used to find a datum point .050” ± .0005” away from a convex surface.

Contents: Chuck Body, Universal Indicator Holder, Needle Point, Ball Contact, Disc Contact.

Edge & Centre Finder Set (5 Piece)

This digital protractor has a range of 360° split into 4 x 90° quadrants. It is simple to calibrate and the intelligent display changes orientation at 90° and 270° to remain readable. It has a ‘V' groove on the top and bottom for easy placement on acute angled or cylindrical objects. 3V lithium battery gives up to 2000 hours use. Complete with a leatherette pouch that has a belt loop.

Digital Protractor

Cylinder Type
For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Edge Finder 10.00mm Body

Plain Type Depth Gauge
Designed for measuring flat based recesses. Consisting of a precision ground steel rule and body which are positioned at 90° to each other. The body has precision ground locating faces, with a knurled adjusting/securing nut. 
Rule Length: 150mm (6”)

Protractor Type Depth & Angle Gauge
Ground steel with graduations from 0° - 180° in both directions for fast and accurate measurements. When the rule is positioned to 90° on the protractor it then provides accurate measurements of depth. 
Rule Length: 150mm (6”)

6"/150mm Protractor Type Depth Gauge

Plain Edge Finder 12mm Body

Combination Edge/Centre Finder 12mm Body

Used for marking out lines parallel to a true edge or groove, and also to mark the centre of round bars. Machined base, two pillars, a double ended scriber and an adjustable attachment for holding scribers up to 1/4” diameter on to the pillar. The base has a machined V-groove for use on pipes and round bar and two frictionally held pins which are used as a guide when sliding along the true edge or groove. The angle of the pillar can be finely adjusted with the use of a knurled thumb screw. Supplied with two pillars.
Base dimensions: 80 x 30mm.

Surface Gauge with 9" & 1 2" Pillars

Protractor head for measuring angles up to 180°, graduated to 1° with one machined face, three knurled securing/adjusting nuts and built in spirit level. For combination set KEN-330-3250K.

Spare Protractor Head for KCS300

Designed for carrying convenience. Lightweight - metric only 68g and inch 98g. Supplied in leather wallet.
Spindle diameter: 6mm flat.
Anvil diameter: 6.5mm flat.
Parallelism: 5μm or less.
Conversion chart printed on back of gauge.
Accuracy: +/-0.02mm.

Imperial Thickness Gauge

ProductPage-Title-Mobile

Below

Scheduled_Orders

show_with_global

ProductPage-Add-To-Quotation

show

SearchPage-LeadTimeFilter

ProductPage-Pills-Visibility

Expanded

InfoPage-DiscountCodes

experiment_1

ProductPage-Attribute-Selector

VariantThreeDropDown

SearchPage_Top_Category

Default

SearchPage-FilterPanel-Expanded

Show

Personalised-BoostType

personalised_boost_v1

Number-Of-Recommendations

seven

SearchPage-SearchResultLimit

Hundred

ProductPage-ViewAll-Terminal-Node

ProductPage_Bundle

two_products

FamilyPage-Attribute-Selector

StickyFilterPanel-InfiniteScroll

Hide

SingleLine-ProductHeader-Mobile

SHOW

Previously-Purchased-Tag

Discount-PromoLabel

hide

Sticky-MainMenu

New_Login_Registration_Toggle

ProductPage-AddToBasket-Mobile

ProductPage-Title-Length-Mobile

Vertical-Recommendations_Toggle

SearchPage-Enable-Sort-Attribute-Value

AttributeValueSortOnSearchAndCategory

Recommendations

test

MyaccountPage_Recommendations

SearchPage-BoostType

boost_img_lt_atb_gp

search-templates

defaultTemplate

Header-MainMenu

Payment-GooglePay

SearchPage-InfiniteScroll-Limit

Thousand

Browse our original Kennedy products in Precision Measuring Tools

We suggest upgrading to Chrome